Last Updated on March 4, 2023
If you do not know what does it mean by 5d code in Whirlpool washer, then you are at the right place. Whirlpool washer displays a 5d error code when the machine loses its ability to drain due to too much foam.
This hinders the normal wash cycle, or the washer takes too long to rinse clothes. This scenario often happens when you normally add water, clothes, and detergent inside the washer and press the start button. Instead of functioning smoothly, the machine will take pauses or slow down the washing process.
So, how can you avoid such situations? In this post, we will describe some of the causes of code 5d in the Whirlpool washer and effective ways to resolve this error.
What Does Error Code 5D Mean in Whirlpool Washer
People often misinterpret 5d code due to similarity in the S and 5 words displayed on the panel. S represents the Sud error which is often confused by 5d code.
However, code 5d shows up on display when there is excess amount of foam inside the washer. The washer takes extra pauses or stops working to extend the rinse cycle. More water and extra time will be required to remove the excessive foam.
The machine shows some responses to fix this problem by shrinking the foam, but if this strategy doesn’t work, it will stop functioning. The 5d error code will start blinking on the screen, and the system will require a quick solution.
What Causes Error Code 5D In Whirlpool Washer
The initial signs of this problem can be noticed when too much foam is drained after washing. This will reveal that your washer isn’t treating detergent well. Usually, the washer doesn’t deplete water having extra foam. There could be several other reasons, and some of them are described below:
Extra Detergent
Putting a large amount of detergent in the washer leads to this 5d error code. You must ensure to use the recommended quantity of detergent.
Using hard water or softeners also hinders the proper mixing of detergent and creates too much foam to drain outside the washer.
Type of Detergent
Not only does the amount of detergent matter, but the type of it also help in maintaining or disrupting the normal operation of a washer. It is highly recommended to use only High-Efficiency detergents to avoid this error.
Some detergents are low in quality which also restricts normal operation. If you notice any changes after using low-quality detergent, try to replace it with a high or better-quality detergent. Using a liquid detergent will prove good for the overall system.
Blocked Drain System
Under certain circumstances, a washer’s drain system gets blocked, preventing water flow at a normal rate. The drain system of a Whirlpool washer includes a drain hose, pipe, hose, sewer entrance, and a filter.
The whole system will be disturbed if anything gets stuck in any of these components. However, you can fix it by unplugging the power source and examining each component properly to search for any obstructions. Wash these parts with pressure to eliminate any blocking material.
Defective Foam Sensor
The problem could also arise due to a defective foam sensor. The sensor won’t be able to identify the amounts of foam. You can use a multimeter to inspect the sensor. Wrongly installed foam sensor can also cause this error.
How to Fix Code 5D Whirlpool Washer
The Whirlpool washer has an automatic system to fix this 5d code error by reducing loads of foam. However, if the problem gets more complicated and the whole system stops functioning, you must resolve it as soon as possible.
As every problem comes with a possible solution, you can fix this one without much effort.
Get Rid of Extra Detergent
The best solution to code 5d in the Whirlpool washer is to reduce the amount of detergent you use. Measure the quantity each time you put it inside the washer.
You may need to change the detergent if the right amount is already being used. If you are using a low-quality detergent, replace it with a high-efficiency detergent or liquid detergent.
If residual detergent is left in the washer, run the wash cycle for a long time to remove all the soap and foam. You can also put some vinegar to remove the residues of detergent. However, you must check if the Whirlpool washer is safe for vinegar use.
Minimize The Heavy Loads
The error code may show up when heavy loads are inside the washer. First, remove some clothes from the drum and run the wash cycle. The error should disappear if this were the cause of the problem.
Inspect Drain Hose
Sometimes, issues in the drain system lead to 5d code that can be fixed by making corrections in the components of the washer. You need to clean all the components such as the filter, drain pipe, and hose to remove obstructions. If any part is damaged, you may go for replacement.
Faulty Controller for Water Pressure
If you turn on your washer, but it doesn’t work, the problem could be with the pressure controller. Your washer may stop working in the middle of the wash cycle. The best way to test is by using a multimeter.
Resetting the water pressure control switch or replacing it will resolve the issue, and the error code will disappear.
Examine Main Control Board
If the problem exists after trying all the above methods, you must check the control board. Examine all the pins, tracks, and wires attached to it. A multimeter is also useful for this purpose. Look for burned or melted wires and replace them immediately. This can only be fixed by replacement as no repairs can be made to it.
Final Thoughts
We hope this guide will help you fix the 5d error code in the Whirlpool washer. However, the summarization of all tips includes using only washer-safe detergent, using only Teaspoon of detergent, washing in soft water, and replacing items that are defective such as pressure controller, drain system, and control board.
Leave a Reply