How to Clean A Shark Vacuum : Things To Follow

Last Updated on September 17, 2022

The Shark vacuum has its mark among some of the most trusted and high-performance vacuums. It has been verified by their manufacturer that, just like Dyson, Shark vacuums have never-ending suction power.

However, after performing a tough cleaning job, these vacuums can build up dirt and debris that must be removed. If you are finding a way to clean a Shark vacuum cleaner, here is the easiest and most accurate procedure.

You will learn how to empty and clean a Shark vacuum without effort or wasting time.

Why Should You Clean Shark Vacuum?

Cleaning a Shark vacuum is necessary as you may not want it to blow up after ignoring its maintenance. Although Shark vacuums have an automated system to alert users by emitting smell and sound, you should also ensure everything is working smoothly. Some of the most common reasons to clean shark vacuum are:

• When you clean too much dirt in one session, lots of dirt and debris accumulate in different components of the vacuum, making cleaning necessary.
• If your Shark vacuum produces awkward sounds during operation, it could be due to a problem in the motor.
• Sometimes obstructions block the filter and induce loss of suction in a vacuum.
• Burning or other smells from a vacuum are also signs of some problems. 

Process Of Cleaning

How To Empty, Clean, And Take Apart A Shark Vacuum Cleaner!

Any of the reasons mentioned earlier can hinder the smooth running of your Shark vacuum or may lead to complete loss of suction. Fortunately, you can clean all parts of your vacuum cleaner without any trouble. A detailed step-by-step process is described below to assist you in cleaning a Shark vacuum cleaner.

Items Require For Cleaning

The following things are required to clean a Shark vacuum cleaner:

• A piece of Cloth or towel
• Toothbrush
• Warm water
• Cleaning Liquid
• Wood skewer
• Scissors
• Flashlight
• Protective gear

Disassemble Components of Vacuum

• Disconnect the power supply and unplug your vacuum before taking it apart.
• You just need to remove some components, such as the dust cup, canister, filter, and hose.
• Take pictures of components before removing them from their place so you can put them back accurately. 

How To Clean A Shark Vacuum 

• Canister

• The next part you need to clean is the canister. Detach it from the vacuum and remove dirt from it.
• Make a soapy water solution and put a canister inside it. 
• To remove tough dirt particles using cloth.
• Use cold water to rinse it thoroughly and let it rest to air dry for some time.
• Make sure to dry it completely before inserting it back into its position.

• Filter

Two types of filters are installed in shark vacuums, each requiring a different cleaning method.

• One of them is a primary filter which is formed of foam rubber. Another secondary filter is usually manufactured of felt. Before cleaning, you must detach filters from the position.
• A HEPA filter is also installed in these vacuums that should only be hand washed. Any harsh cleaning agent or soap should never be used for cleaning. 
• Rinse both filters under cold water and let them air dry.

Always reinstall filters after drying them completely. Inserting a wet filter will develop mold and also cause damage to the vacuum. It is also recommended to wash the HEPA filter at least once a year during the primary filter every month.

• Hose

• You can use a large sink to wash the hose. It is better to wash it somewhere outside instead of the kitchen sink.
• Fill hot water in the sink and add a small amount of a mild cleaning agent.
• Now put the hose inside the water and detergent solution.
• Use a towel or cloth to rub parts of the hose to eliminate any gunk stuck on the surface.
• Make another solution by adding baking soda and white vinegar.
• Put this mixture inside the hose from one end to another. For a better outcome, shake the mixture in the hose well until you see bubbles.
• Now rinse it thoroughly to remove all cleaning solutions as well as dirt.

Make sure to clean the motorized floor nozzle and duct hose attached to it. Its cleaning can be done the same way you did for the hose.

• Roller

After cleaning the filter and hose, the next part which needs attention is the brush roller. Tangled hair, strings, threads, and lots of debris could be wrapped around its bearings. Usually, the suction power gets affected by a clogged roller.

• First, separate the floor attachments from the handle of the vacuum.
• With the help of scissors, cut the threads or hair tangled with the brush.
• Use a cleaning brush or toothbrush to remove dust.
• You must clean these parts with great care as any mistake can damage the brush’s bristles.
• For deep cleaning, you can also wash it with cold water and reinsert it after drying.

Reattach All Components

Once all components of the Shark vacuum are cleaned, you must reattach them back to their previous position without damaging any part. We’d highly suggest drying each part completely before inserting back. Attaching wet or even damp parts will badly damage your vacuum and also cause mold and bacterial growth,

After assembling each component, wipe the outer surface of the Shark vacuum with the help of a clean cloth. Also, spray some good fragrance to give it a fresh and new feel.

How Often to Clean A Shark Vacuum

Most experts suggest cleaning a Shark vacuum at least four times a year. However, this can vary depending on the use and situation of your home. If there are loads of dirt, you need to clean it more often.

Whenever you notice any signs of malfunctioning, start its cleaning right at the moment without delays. These vacuums are made to last for years and guaranteed never to lose suction, but if your unit is not sucking up dirt correctly, it is in dire need of cleaning.