How to Drain Water From Automatic Washing Machine Manually?

Last Updated on November 14, 2022

You’re doing a load of laundry, and suddenly, you hear this strange noise from the washing machine.

What causes it?

It sounds like the water is backing up and overflowing from the machine.

It can happen when there’s too much water in the tub, and it can’t drain properly.

In this article,  we’ll show you how to drain water from an automatic washing machine manually. Let’s move on!

How to Drain Water From Automatic Washing Machine Manually 

Draining water from an automatic washing machine manually is not a big deal. But you will succeed only when you know how to do this.

Draining the water from an automatic washer becomes too easy with a few tricks in mind. We have discussed some practical tricks in the later section. Stay connected till the end to learn all about it!

Requirements

Before you start, you will need a bucket and a screwdriver. Ensure you have both these items before you start the process. Follow these steps to manually prepare the washing machine area to drain water from it.

• Find the Drain Pump

First of all, locate the drain pump. It’s usually in the lower front of the machine.

• Remove the Pump Cover 

The pump will have a cover, and you will need to remove it. Use a screwdriver to take off the Pump cover.

• Open the Pump in the Bucket

Once the cover is off, you should be able to see the pump. The bucket goes under the pump, and then you can use the screwdriver to turn the pump on. It will start to drain the water from the machine.

Remember that this process can take a while, so be patient!

Step-by-Step Procedure

Okay, so you’ve got a full load of laundry, and you’re ready to start the washing machine. But then you remember—you forgot to drain the water out of the machine from last time!

Don’t worry; it’s quite easy to fix it. Follow these six simple steps:

 

1) Locate the drain hose. It’s usually attached to the wall near the washing machine.

 

2) Disconnect the hose from the washing machine.

 

3) Place a bucket or container under the open end of the hose.

 

4) Carefully remove the clamp that holds the hose in place.

 

5) Allow the water to drain from the hose into the container.

 

6) Reconnect the hose and reattach the clamp.

Draining the Water Manually

Well, before you start tearing your machine apart, try manually draining the water. It is a process that’s a lot simpler than it sounds.

Here’s how to do it:

• First, find your washing machine’s drain hose. This hose connects your machine to the drain pipe in your wall or floor. The hose will either be attached to your machine’s back or on the side.

 

• Once you’ve found the hose, disconnect it from the machine and place it in a bucket or sink. Then, open the faucet and let the water run until the bucket or sink is full. Once it’s full, close the faucet and reattach the hose to your machine. Voilà! The water is now drained.

Draining the Bleach Manually

You’ll need to open the washing machine drain valve when it’s time to drain the bleach. It is the little knob that’s usually on the front or back of the machine, and it’s what you use to let the water out.

Once you’ve opened the valve, you can let the water run out into a bucket or down the drain. If you’re going to let it run out into a bucket, make sure you have a container that can hold at least five gallons.

If you’re going to let it run down the drain, you’ll need to open up the sink faucet and put the hose in there. Keep in mind that the water might be hot, so be careful when you’re handling it.

Draining the Fabric Softener Manually

Do you know how to manually drain the fabric softener from the automatic washing machine? If not, don’t worry—we’ll show you how.

First, you’ll need to open up the fabric softener compartment. It’s usually located on the top of the machine. Once you’ve found it, locate the drainage hole and put the end of the drain hose into it.

Now it’s time to open the faucet valve and remove all water from it. Ensure you keep an eye on the hose to ensure it doesn’t get kinked or twisted.

And that’s it! You’ve successfully drained the fabric softener from your automatic washing machine manually.

Draining the Detergent Manually

Okay, you know how to drain the water from your machine manually. But what about the detergent?

You’ll need to remove the detergent drawer and dump any excess water. Once you’ve done that, replace the drawer and run a cycle without any clothes in the machine. It will help dry the interior and eliminate any remaining detergent or soap residue.

Effective Tips

Here are a few important tips to keep in mind:

• First, always unplug the washing machine before attempting to drain the water.
• Next, locate the drain hose. It is usually located at the bottom of the washing machine.
• Once you’ve located the drain hose, detach it from the washing machine and place it in a bucket or sink.
• Ensure the bucket or sink is positioned below the level of the drain hose; otherwise, you’ll end up with water all over your floor.
• Now it’s time to open the faucet valve and let the water flow out of the hose until it’s clear.
• Finally, reattach the hose to the washing machine and plug it back in.

Conclusion

Now that you know how to manually drain water from an automatic washing machine, the next time your machine overflows, you’ll be ready to take care of the situation yourself.

Remember to be careful – you don’t want to get injured. And always consult your machine’s manual for more specific instructions.

Hopefully, this guide will help you drain water from the automatic washing machine manually. Stay connected for more cleaning tips from us!